Garage Door Sensor Repair & Replacement Perth
Door won't close, reverses halfway or the opener light flashes? We realign, rewire or replace the safety sensors and reset the opener so the door closes first time, across Perth.
- Photo-Eye Sensors
- Same-Day Visits
- Safety Reverse Tested
- All Perth Suburbs

Closes First Time
Quick Answer
Capital Garage Doors repairs and replaces garage door safety sensors across Perth. The two photo-eye sensors at the bottom of the door opening are the usual reason a door refuses to close, stops and reverses, or closes only while the wall button is held down. We realign and clean the sensors, repair chewed or corroded wiring, replace a failed sensor pair with one matched to your opener, and reset the opener's force and travel limits, then prove the safety reverse before we leave. If the fault is the opener's board rather than the sensors, we repair that on the same visit.
Why Garage Door Sensors Fail, and How We Fix Them Properly
The safety sensors are a transmitter and a receiver mounted a hand's width above the floor on each side of the opening. They throw an invisible beam across the doorway and the opener will not close the door unless the beam is unbroken. It is a simple system and that is its weakness: a wheelie bin, a leaf blower's dust, afternoon sun straight into the receiver, a bracket knocked by a car bumper or a wire nicked by a rake will all break the beam, and the door behaves as if something is in the way.
Most sensor call-outs in Perth are alignment and wiring. One bracket has been bent so the beam misses, or the low-voltage wire that runs up to the motor has corroded at a joint, been crushed under a wheel or eaten through by a rodent. We re-set the brackets so both indicator lights hold steady, repair or re-run the wiring in conduit where it keeps getting damaged, and shield a receiver that faces the setting sun. When a sensor has genuinely failed we fit a pair matched to the opener's brand, because a mismatched generic pair is the second most common reason a door still will not close after a DIY fix.
Sometimes the sensors are fine and the opener is the problem: a logic board that no longer reads the sensor circuit, or force and limit settings that make the door reverse before it reaches the floor. Our technicians carry sensors, boards and remotes for the common Perth openers, so the visit ends with a door that closes, not a second appointment. If you would rather try the easy checks first, our guide to fixing a garage door sensor is linked below.
Common Problems We Fix
What's Included
- Sensors cleaned, realigned and brackets re-set
- Low-voltage sensor wiring repaired or re-run in conduit
- Failed sensor pair replaced with one matched to your opener
- Sun-glare shielding where the receiver faces the afternoon sun
- Opener force and travel limits reset after the repair
- Safety reverse tested with a block under the door
- Logic board or opener repair on the same visit if that is the fault
- Same-day visits across Perth; a fixed quote agreed first
How Our Repair Process Works
Tell us what the door does
Won't close at all, reverses part-way, or closes only with the button held: each points to a different fault and we bring the right parts.
Check the beam
Both sensor lights are read at the door and at the motor to separate an alignment or wiring fault from a failed sensor or board.
Fix the cause
Brackets re-set, wiring repaired or re-run, or a matched sensor pair fitted; a failed board is repaired or replaced.
Reset the opener
Force and travel limits are set so the door reaches the floor and seals without reversing.
Prove the safety reverse
The door is closed on a block and must reverse; a door that does not is not safe to leave.
Cost Guidance
Straight from our price list. Sensor work is priced as a pair with attendance included; if the opener's board turns out to be the fault, the repair row applies instead. As a guide:
| Scenario | Guide Price | Notes |
|---|---|---|
| Safety sensors / photo eyes | $150–$300 | Replace and realign the safety photo-eye sensors. |
| Motor / opener not working (repair) | $380–$490 | Diagnose & repair the opener — gears, logic board, capacitor or limit switches. |
Final pricing depends on the cause, parts required, and door size — confirmed on inspection before any work begins.
More on pricing:Full Perth garage door price list
Why Choose Capital Garage Doors
Cause, not symptom
We read the sensor circuit at the door and at the motor, so a wiring or board fault is not misdiagnosed as a sensor.
Matched sensors
Replacement pairs are matched to the opener's brand, which is why they keep working.
Wiring done once
Damaged runs are re-run in conduit so the same fault does not come back next summer.
Safety proven
Every visit ends with the safety reverse tested; a door that will not reverse is not left in service.
Opener expertise
If the sensors are fine and the board has failed, the same technician fixes the opener on the spot.
All of Perth, same-day
A door that will not close is a security problem, so sensor jobs are booked as priority visits.
Areas We Service
Capital Garage Doors provides this service across Perth, including:
Don't see your suburb? We still likely cover it.
Request QuoteWhat Perth Homeowners Say
“Great service. The team attended super quickly and solved the problem in minutes. They also previously replaced a broken motor in very quick time and at a very reasonable price. Can't recommend highly enough.”
Ross L. · Motor Replacement
“Had an issue with the motor on an old SDO-1 unit. Called on a Monday, asked for Wednesday morning, and he came in early and gave me options. I chose to fully replace my system and rollers, and he removed the old system and rails too. Quick and easy — not even 45 minutes, with no issues.”
Jacques D. · Motor Replacement
“Thank you Capital, and special thanks to Mr. Musab and Mr. K for this perfect and more than wonderful work. The motor and spring were replaced with great precision and speed. Very nice and respectful people.”
Kasem S. · Motor Replacement
Frequently Asked Questions
Sensors are priced as a pair on our price list, and the guide-price table on this page shows the current figure, which includes attendance, fitting, wiring and alignment. Many sensor call-outs do not need new sensors at all: a realignment or a wiring repair is charged at the lower end. If the opener's logic board is the real fault, the opener repair row applies instead, and we tell you which it is before any work starts.
Get a quote
Book Garage Door Sensor Repair in Perth
Licensed, insured, and local. Send the form and we'll get back to you fast with a fair, no-obligation quote — or call now and speak to a technician.
- 0475 333 335
- 13 Amrock Street, Southern River WA 6110
- Mon–SunOpen 24 hours
Request a Free Quote
Prefer to call? 0475 333 335Ready to upgrade your
garage door experience?
Whether you need an emergency repair right now or a smart quote for a new installation, we've made getting help faster and easier than ever.